SAE J1098 Ton Kilometer Per Hour Application
时间:2024-05-18 15:37:45 来源: 标准资料网 作者：标准资料网 阅读：8482
Product Code:SAE J1098
Title:Ton Kilometer Per Hour Application
Issuing Committee:Mtc8, Tire And Rim
Scope: This SAE Standard establishes the procedures for the application of Ton Kilometer Per Hour (TKPH) rating values for off-the-road tires; utilizing empirical data formula, it describes the procedure for evaluating and predicting off-the-road tire TKPH requirements as determined by a work cycle analysis. This document is applicable to only those tires used on earthmoving machines as defined in SAE J1057, and contains machines referenced in SAE J1116. The loads, speeds, inflations, and rim configurations are assumed to be within acceptable industry or manufacturer's prescribed recommendations. Other application parameters affecting tires are not included in the scope (for example: floating, cut, bruise, wear, etc.). These parameters must also be considered for final tire selection, since a tire that maximizes desirable TKPH characteristics will sometimes compromise these other parameters. The standards for the productivity of off-the-road machines to tires are not included in the scope. The formula (4.2 and 4.3) are applicable to transport type machines only (that is, trucks, tractor trailers, and scrapers) usinselection, since a tire that maximizes desirable TKPH characteristics will sometimes compromise these other parameters. The standards for the productivity of off-the-road machines to tires are not included in the scope. The formula (4.2 and 4.3) are applicable to transport type machines only (that is, trucks, tractor trailers, and scrapers) using category E Earthmover Service Code Tires. See SAE J751 for service codes.g category E Earthmover Service Code Tires. See SAE J751 for service codes.
Product Code:SAE ARP1176
Title:Oxygen System and Component Cleaning and Packaging
Issuing Committee:A-10 Aircraft Oxygen Equipment Committee
Scope: This SAE Aerospace Recommended Practice (ARP) provides recommended practices for cleaning aircraft oxygen equipment such as tubing, pieces parts (including regulator and valve parts), cylinders and ground-based equipment that may be used to support aircraft oxygen systems. These methods may apply to gaseous and liquid oxygen equipment. This document specifies work area details, methods to select suitable cleaning chemicals, cleaning methods, test methods to verify cleanliness level, and methods of packaging the components and parts after cleaning. Person designated to clean oxygen equipment should be qualified and trained to clean oxygen equipment. Cleanliness levels achieved are strongly dependent on the capabilities of the persons performing the cleaning operation.
Rationale: This SAE Aerospace Recommended Practice (ARP) provides recommended practices for cleaning aircraft oxygen equipment such as tubing, pieces parts (including regulator and valve parts), cylinders and ground-based equipment that may be used to support aircraft oxygen systems. These methods may apply to gaseous and liquid oxygen equipment. This document specifies work area details, methods to select suitable cleaning chemicals, cleaning methods, test methods to verify cleanliness level, and methods of packaging the components and parts after cleaning. Person designated to clean oxygen equipment should be qualified and trained to clean oxygen equipment. Cleanliness levels achieved are strongly dependent on the capabilities of the persons performing the cleaning operation.【英文标准名称】:Ergonomicdesignofcontrolcentres-Part6:Environmentalrequirementsforcontrolcertres
【原文标准名称】:控制中心的人类工效学设计.第6部分:控制中心的环境要求
【标准号】:JISZ8503-6-2007
【标准状态】:现行
【国别】:日本
【发布日期】:2007-09-20
【实施或试行日期】:
【发布单位】:日本工业标准调查会(JISC)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:
【中国标准分类号】:A25
【国际标准分类号】:
【页数】:30P.;A4
【正文语种】:日语